|
Pole-fishing: Tying pole rigs on the bank
A quick fix pole rig and some stillwater tips.Having the confidence to knock up the
tangled rig in a couple of minutes is useful, especially so on commercial carp waters
where you so often have to fish close to features to get a bite and hooking something
monstrous which is going to tear through the reeds is pretty inevitable. The good news is
that we are not talking fine, complicated shotting patterns with a string of No13 shot set
1.37 inches apart on these waters.
Carp fishing close to features with big baits demands a simple, aggressive approach with
strong line and a very straightforward shotting pattern.
In fact, if you are fishing big baits like paste or meat, you only need a simple bulk of
shot and no droppers at all. The biggest factor of all is balance - matching the line and
the elastic to the peg and the species.
If you are fishing in open water you can afford to look for more bites by fishing quite
light and having an elastic to suit.
If thereТs the odd decent carp about among mainly smaller fish, a No8 elastic to about
0.12mm (3lb) diameter rig line would be ideal in open water.
If, however, you need to fish close to snags and СdragТ big fish out with gritted
teeth, we are talking a tight number 16 elastic and for that IТd use 0.16mm (5.5lb)
diameter line.
Gareth Purnell, Improve Your Coarse Fishing
|
|
|
1.
Choose a float to suit the hook bait and the method. With bigger baits like corn, meat and
worm you are going to need a float with a thick cane bristle. Make sure you have a winder
into which the whole stem, and importantly, the whole body sits neatly.
|
|
|
2.
Line choice is next and it needs to match the elastic and target fish. On this water IТm
actually fishing out in open water for small carp and tench up to about 1lb 8oz and IТm
using a No7 Vespe elastic. This matches quite well with 0.12mm (3lb) diameter rig line.
|
|
|
3.
Line, float and elastic set-up chosen, simply tie an overhand loop in the end of your
spool line and hook over the connector. IТm assuming you know the depth as youТre
already fishing the peg, so just pay out line until it comes near to the end of the
Сswing to handТ section.
|
|
|
4.
Thread the line through the floatТs eye, and then thread on the silicone tubing. You
should always attach a float with three pieces of tubing, not two, in case one splits
during the session.
|
|
|
5.
The depth here is about five feet and IТm using a 0.75gr float. For quick reference I
carry around this card which tells me that a No6 shot weighs .1gr, so IТll need seven of
those and a couple of smaller dropper shot.
|
|
|
6.
Try to line the splits in the shot up if you can, for neatness, and donТt bite the shot
on too hard or you will damage the line and reduce its strength dramatically. On adding
seven No6 shot I find the float is over-shotted. ItТs quite common for the stated weight
not to be totally accurate.
|
|
|
7.
Off comes one No6 and on go No8 shot one by one until the float sits perfectly in the
water. Now, and this is important, you must take one No8 off so the float sits a little
too high. The reason is that when fishing, the weight of the line and the hook will pull
the float down more.
|
|
|
8.
ItТs good practice now to slide all the shot up a few inches and bite off the piece of
line at the bottom of the rig, so there is no damaged line on the rig caused by biting the
shot on too hard.
|
|
|
9.
Tie an overhand loop in the end, closing it into a neat loop using a knot picker, slide
the float up to the marked depth, attach the hooklength and get fishing!
|
|
|
10.
Finally, donТt forget to add the rig details onto the winder.
|